LEEMING & PEEL UK SPRING SUPPLIERS

Coil Springs, Compression Springs, Flat Springs and Tension Springs Manufacturer

When you are looking for a British spring maker, look no further than Leeming & Peel, makers of spring coils and wire springs for 65 years.

Leeming & Peel Springs
Suppliers of coil springs IK suppliers of industrial grade springs suppliers of garage door springs suppliers of clock springs

Below is a good indication of the various types of springs we manufacture, If you have a demand, we can create the spring in single orders, small batches and large quanities

COMPRESSION SPRINGS
Coil Springs | Compression Springs | Flat Springs | Tension Springs

Compression springs are open-wound helical springs that exert a load or force when compressed. They may be conical,barrel,concave or standard cylindrical in shape. The ends can be closed & ground, closed but unground, open & unground & supplied in lengths for cutting.

All types of material can be used including:
Commercial Wire (BS5216 HS3) , Music, Stainless, Phosphur Bronze,Chrome Vanadium, Monel 400,Inconel 600, Inconel X750 , Nimonic 90 :
Round wire, Square & Rectangular sections are also stocked.

When ordering it is very useful to give details of any closely related working parts, such as:

SPRING WORKS IN A HOLE DIAMETER OF 25.5 MM OR SPRING WORKS OVER A ROD OF 15 MM DIA.

The picture above shows an example of a typical Compression spring:
Wire dia. = 2.03 mm (14 gauge) : Outside dia. = 20 mm : Total coils = 7 : Free length = 50 mm : End type = Closed & ground : Spring rate = 5.274 Newtons per mm or (30.13 lbs per inch) Car Coil Springs can be Re Set to Length then re-hardened & tempered then painted.
We also make to order special small batches of car coil springs,even a batch of 2 off is not a problem we have the machines to make them with a fast delivery service.

If you need any help with design work please send us all the information you have to hand.

LEEMING & PEEL CAN MANUFACTURE TO THE TOLERANCES DETAILED IN BS 1726 PART 3 1998 AND CAN PROVIDE MATERIAL TEST CERTIFICATES & CERTIFICATES OF CONFORMITY. WE ARE ISO 9001 : 2008 REGISTERED (monitored BY UKAS) AND ALSO OFFER A FULL CAD DESIGN SERVICE FOR DEVELOPMENT WORK.
IN APRIL 2011 WE GAINED ACCREDITATION TO ISO 9001 : 2008

TENSION SPRINGS OR EXTENSION SPRINGS INCLUDING GARAGE DOOR SPRINGS
Tension springs are exactly the opposite to compression springs, in that they are close coiled helical springs that extend under a pulling force.

There are many different end types:
FULL LOOP: REDUCED DIA. LOOP: ENLARGED DIA. LOOP OR HOOK : HOOK END : DOUBLE TWISTED LOOP : EXTENED HOOK END : CONED END WITH SWIVEL HOOK OR LOOP : CONED END WITH SWIVEL BOLT : PLAIN SQUARE CUT ENDS : LOOPS OR HOOKS CAN BE OFFSIDE OF BODY :

When ordering Tension Spings please specify:
WIRE DIA. =
OUTSIDE DIA. =
INSIDE LOOP (HOOK) =
END TYPE =
SPRING RATE =
REQUIRED DEFLECTION =
We have a stock range of Birtley & Henderson Garage Door Springs, please ring for details.

FLAT SPRINGS
Flat Springs are made of flat strip, including high-carbon spring steel : stainless steel : beryllium-copper : & other exotic alloys. They are used in restricted space conditions where the deflection required is usually small. Many types of intricate radius bends & punched holes make up the design of Flat Springs.

TORSION SPRINGS
Torsion Springs are helical coil springs that exert a torque or rotary force . These springs can be wound either LEFT HAND or RIGHT HAND. Deflecting them causes the spring to wind up from the free position , never to unwind (this causes breakages) thus the inside dia. gets smaller. Such springs should be supported over a rod where possible. The legs can be bent into many different forms for each specific application.

SPRING COATINGS & SURFACE ENGINEERING
All Springs can be plated (zinc,chrome,gold,chemical black,galvanised)or painted (colour coded) to your specification.
We can also Shot Peen or Bead Peen Compression Springs on request thus greatly improving the fatigue life of the springs.

WIRE STRAIGHTENING & CUTTING
Round Wire in coil can be straightened up to 6.35 mm (.250") in dia. & cut to your required length.Normal spring wire,stainless,pre galvanised,phosphor bronze are all types of wire that can be straightened

Clock Type Springs
Flat strip spring steel is wound in a circle to provide a force when coiled up smaller in diameter.Many end types can be manufactured to your requirements, but the inner dia. is normally supported on a shaft with a slot cut across the middle to accept the strip.


A SPRING IS A CONTRIVANCE FOR STORING ENERGY

SNAP RINGS & CIRCLIPS
We are able to supply inner & outer type snap rings & circlips up to 12 mm BS/5216/HS3 wire diameter with outside diameters up to 350 mm

Agricultural Springs(Farm Springs)
We can supply most types of farm machinery & general agricultural springs.All we need is a sample or sample details or even a quick sketch of your requirements.
Please Ring On 01274-491464

GARAGE DOOR SPRINGS
We have made garage door springs for over 25 years.We stock Birtley Garage Door Springs, colour codes ,Black,Red,Green,Yellow,Silver,Black/Red Stripe,Black/White Stripe,Blue,Orange & some of the Henderson Dolphin Garage Door Springs(colour codes grey,green,black)
Please ring for details on 01274-491464


If you have a demand, we can create the spring in single orders, small batches and large quanities


CREDIT/ DEBIT CARD PAYMENTS ACCEPTED

Made In Britain

Leeming and Peel Ltd

DUNCOMBE STREET
OFF INGELBY ROAD
BRADFORD, BD8 9AJ
Phone: TEL: 0044 (0)1274 491464
Fax Phone: FAX: 0044 (0)1274 481690
E-mail: lpsprings@aol.co.uk